# Generado por:
<br /># DD-WRT
<br /># 
<br /># unsolclic version: v3.6-beta
<br /># open a telnet/ssh session on your device and run the script below.
<br /># Note: Use Status/Wireless survey to verify that you have the
<br /># antenna plugged in the right connector. The right antena is probably
<br /># the one which is at the right, looking the WRT54G from the front
<br /># (where it have the leds). If needed, change the antenna connector
<br /># at Wireless->Advanced Settings.
<br /># Security notes:
<br /># Once this script is executes, the router password for root/admin users is "guifi"
<br /># You must change this password if you want to keep it secret. If you like to still
<br /># be managed externally, you must install a trusted ssh key. Upon request, your setup
<br /># might be asked for being inspected to check the Wireless Commons compliance.
<br /># No firewall rules are allowed in the public network area.
<br /># By being in client mode, the router has the firewall enabled to distinguish between
<br /># private and public areas, and only SNMP, ssh and https 8080 ports are enabled
<br /># for external administration. Everything else is closed, therefore you might
<br /># have to open ports to share resources.
<br /># 
<br /># Xintcat-PLAFORQUESRadio3
<br /># Global network parameters
<br />nvram set router_name="Xintcat-PLAFORQUESRadio3"
<br />nvram set wan_hostname="Xintcat-PLAFORQUESRadio3"
<br />nvram set wan_proto="disabled"
<br />nvram set lan_domain="guifi.net"
<br />nvram set wan_domain="guifi.net"
<br />nvram set http_passwd="guifi"
<br />nvram set time_zone="+01 2 2"
<br />nvram set sv_localdns=""
<br />nvram set wl_net_mode="b-only"
<br />nvram set wl0_net_mode="b-only"
<br />nvram set wl_afterburner="on"
<br />nvram set wl_frameburst="on"
<br />nvram set txpwr="28"
<br />nvram set txant="0"
<br />nvram set wl0_antdiv="0"
<br />nvram set wl_antdiv="0"
<br />nvram set block_wan="0"
<br /># 
<br /># Management
<br />nvram set telnetd_enable="1"
<br />nvram set sshd_enable="1"
<br />nvram set sshd_passwd_auth="1"
<br />nvram set remote_management="1"
<br />nvram set remote_mgt_https="1"
<br />nvram set snmpd_enable="1"
<br />nvram set snmpd_sysname="guifi.net"
<br />nvram set snmpd_syscontact="guifi_at_guifi.net"
<br />nvram set boot_wait="on"
<br /># This is just a fake key. You must install a trusted key if you like to have you router managed externally
<br />nvram set sshd_authorized_keys="
<br />ssh-rsa AAAAB3NzaC1yc2EAAAABIwAAAIEAwWNX4942fQExw4Hph2M/sxOAWVE9PB1I4JnNyhoWuF9v\
<br />id0XcU34kwWqBBlI+LjDErCQyaR4ysFgDX61V4kUuCKwBOMp+UGxhL648VTv5Qji/YwvIzt7nguUOZ5A\
<br />GPISqsC0717hc0Aja1mvHkQqg9aXKznmszmyKZGhcm2+SU8= root@bandoler.guifi.net\
<br />"
<br />nvram set http_enable="1"
<br />nvram set https_enable="1"
<br /># 
<br /># NTP Network time protocol
<br />nvram set ntp_enable="0"
<br /># 
<br /># AP mode
<br />nvram set wl_mode="ap"
<br />nvram set wl0_mode="ap"
<br />nvram set wl_channel="1"
<br />nvram set wl_ssid="guifi.net-XintcatPLAFORQUESRa"
<br />nvram set wl_macmode="disable"
<br />nvram set wl0_macmode="disable"
<br />nvram set wl_macmode1="disable"
<br />nvram set wl0_macmode1="disable"
<br /># 
<br /># Firewall disabled
<br />nvram set filter="off"
<br /># DD-WRT OSPF routing
<br />nvram set wk_mode="ospf"
<br />nvram set routing_lan="on"
<br />nvram set routing_wan="on"
<br />nvram set routing_ospf="on"
<br />nvram set dr_setting="3"
<br />nvram set dr_lan_rx="1 2"
<br />nvram set dr_lan_tx="1 2"
<br />nvram set dr_wan_rx="1 2"
<br />nvram set dr_wan_tx="1 2"
<br /># 
<br /># DHCP
<br />nvram set dhcp_start="5"
<br /># 
<br /># 
<br />nvram set rc_startup="#!/bin/ash
<br /># 
<br />#  unsolclic: v3.6-beta
<br />#  radio:     1873-Xintcat-PLAFORQUESRadio3
<br /># 
<br />    /bin/sleep 5
<br />    /bin/kill -9 \`/bin/ps |/bin/grep bird|/usr/bin/cut -c1-5|/usr/bin/head -n 1\`;
<br />    /bin/rm /tmp/bird/bird.conf
<br />    /bin/echo -e 'router id ;
<br />    protocol kernel { learn; persist; scan time 10; import all; export all; }
<br />    protocol device { scan time 10; }
<br />    protocol direct { interface \"*\";} 
<br />    protocol ospf WRT54G_ospf {
<br />    area 0 { tick 8;
<br />    interface \"*\" { cost 1; hello 10; priority 1; retransmit 7; authentication none; };
<br />    };
<br />    }
<br />    ' >/tmp/bird/bird.conf
<br /># 
<br />    /bin/sleep 3
<br />    bird -c /tmp/bird/bird.conf
<br />    /usr/sbin/wl shortslot_override 0
<br />    ifconfig eth1 -promisc -allmulti
<br />    ifconfig br0 -promisc -allmulti
<br />    ifconfig eth0 promisc"
<br /># 
<br /># end of script and reboot
<br />    nvram commit
<br />    reboot
<br />